6 Volt Electrical Generator for Motorized Bicycle Light

Description

Super Dynamo Lighting
Bicycles and Motorized Bikes…Avoid
Accidents…Avoid Tickets…Get Lights!
Motorized
Bicycle Lighting
6 Volt Mini-Generator
12 Volt Mini-Generator Max
6 Volt Mini-Generator With
Switch
12 Volt Mini-Generator With
Switch
6 Volt Mini-Gen for Pull Start
Engines
12 Volt Mini-Gen Max for Pull
Start Engines
Complete 6 Volt Lighting System
LS-1
Complete 7.2 Volt Lighting
System LS-2
Complete 12 Volt Lighting
System LS-3
Enclosed Light Switch SPST
Enclosed Light Switch SPDT
Encased 6 Volt SLA Battery
Encased 7.2 Volts AA Battery Pack
Encased 14.4 Volts AA Battery Pack
6 Volt Mini-Charger For LS-1 and
LS-2
12 Volt Mini-Charger for
LS-3
Magneto Coil Mini Charger
Magneto Coil Lighting System
Heavy Duty Headlight Bracket
Heavy Duty Tail Light Bracket
MINI-GENERATOR

For Motorized Bicycles
This is a Mini-Generator made to

provide electricty for 6 volt lighting of about 3 to 5 watts. This item is easily

installed and includes instructions for installation. .
The second and third photos

below illustrate the Mini-Gen installed into the engine’s magneto housing. This “Mini-Gen”

is a mini generator and will produce reliable electricity for all common 6v 3w headlight

systems.
This generator will run lights of higher wattage, but for best all around

performance, a 3 to 5 watt lighting system is recommended. Just install into magneto case

using the 2 rear magneto screws, then route red (output) wire through wire harness. The

red wire from the MINI GENERATOR will send electricity to your lights through a light

switch or connected directly for continuous light.
For a more stable lighting system

you can add a Mini-Charger and battery pack available in our store (links on left

side).
NOTE:
Please feel free to inquire about pricing for any single

item(s).
Install this mini-generator and get lights for your motorized bike.
No more troubles from dead batteries and flimsy lights.
We also have available a light switch and other accessories for this item.
Click on the links on the left to check out our other items.
Just remove the engine magneto cover, then use the 2 rear screws to attach Mini-

Generator inside engine magneto case.
Remove wire grommet at the front (white plastic or black rubber) then insert Mini-Gen

wire into grommet.
Use a pick or small screwdriver or nail to push into the area where wire will fit,

then insert wire.
Instructions and precautions are included for Mini-Gen installation.
After the Mini-Generator is installed, the power wire should be routed toward bicycle

seat post for Mini-Charger connection, unless it’s being used for other purpose.
Position wire inside case away from moving parts and also make sure it will not be

pinched under the cover.
Use duct tape (any color) or cable ties to secure wire onto bike’s bottom bracket and

seat post.
The Mini-Gen in this photo is connected to the red wire coming from the Mini-Charger.

Your results will look far better than this one.
Here

is the Mini-Gen’s voltage being measured.
The Mini Gen here is producing a little over 6 volts for all 6 volt lighting systems

and accessories.
This is called a generator (which technically produces dc voltage), but this produces AC

voltage.
The engine speed here is around 900 to 1000 RPM which is just a little

above idle speed.
Most riders will produce this voltage at a slow speed of around

12 to 15 MPH.
Higher voltages of around 12 or more is obtainable at much higher engine speeds, but 6

volts is recommended for all around best performance.
The Mini-Gen is seen here

hooked up to a common 6 volt / 3 watt bicycle headlight and tail light .
This type of lighting is rated at around 500 milliamps (1/2 AMP), but it was tested

on a fully charged 6 volt battery and used about 0.435 amps (or 435 milliamps).
Here in the photo you see the light using 424 milliamps at just a little over idle

speed.
Unlike most LED lights, regular light bulbs will run off both AC and DC

voltage with no problem.
Caution:-
If running lights directly from Mini-

Gen, avoid revving up the engine with lights on because high revs for more than 5 seconds

can immediately blow the bulbs.
High speeds while driving is perfectly o.k.
Example of a 6 Volt Lighting System
A

photo of a popular 6 volt / 3 watt bike lighting system is seen here.
This ad is for a Mini-Gen
only
and does not include lights.
Check out our other ads for Mini-Gens which include lights and other

accessories.
Please note that some 6 volt light bulbs will perform better than

others.
A 6 volt bulb of higher amperage or wattage rating does not necessarily

shine brighter.
A common 3 watt bicycle dynamo type headlight and tail light are seen in this

photo.
PAYMENTS
Payments for auction items are expected
within 3 days, but no later than 7 days. All payments accepted through Paypal or CIP.
Serious inquiries about payment for individual items welcome.
SHIPPING
Flat rate shipping & handling price
is available
for the continental USA. Shipping & handling might also be the same for other states

outside the
continental United States. This item will normally ship within 2 business days,
but could take up to 5 business days. To check shipping and handling fees to your state

just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page.
Items will be shipped to the address provided for transaction. Request to change shipping

address after item is shipped will be ignored.
We reserve the right to refuse shipment

to uncomfirmed addresses in which case buyer will be refunded.
INTERNATIONAL
shipment is available with
slightly higher fees. To check shipping and handling fees to your country just click on

the SHIPPING AND PAYMENTS button below top photo on this eBay page.
WARRANTY & RETURNS
The SUPER DYNO Lighting
System (patent pending) is warrantied for 7 days cash back, and 30 days replacement. If

you
are unsatisfied for any reason, just return the complete kit, and a refund will be issued
(less shipping and handling). Shipping & handling is not refundable, and the customer

is
responsible for shipping cost of the returned item.If any problems are experienced with

our products, please contact us for assistance before resorting to any other course of

action.
NOTE- Any item showing signs of
tampering or abuse will void warranty!
INTERNATIONAL
customers are legible
for the 30 days parts replacement warranty ONLY. Customer is responsible for shipping
returned items.
DISCLAIMER
This “SUPER DYNO Lighting System”,

and all
parts, pieces, ideas and designs associated therewith, are the proprietary rights and

ownership
of Wonderful Creations Store. Any copying, modifying, tampering and or false claims are
discouraged and expressly prohibited.
By purchasing this system you agree to abide

by
any and all traffic laws governing your city, state or country and further agree to hold
Wonderful Creations and any associates thereof, blameless for any accidents, mishaps,

property loss,
damages, death, injuries or expenses reportedly, or supposedly caused by the use, or

misuse
of this lighting system.
Copyright © 2004-2010 Wonderful Creations . All rights

reserved.